![]() ![]() The name is taken from the SEND CUE SHEET command (as defined in the SCSI-3 Multimedia Commands specification), used for sending a binary-format cue sheet describing the disc layout to the drive before writing starts in SAO (Session-At-Once) write mode. The official cue sheet specification is widely accepted to be Appendix A of the CDRWIN User's Guide. The format has since been adopted as the de facto standard, and is used by various other applications, including the audio player foobar2000. The cue sheet format was invented by Jeff Arnold of GoldenHawk Technology for use with his DAO ( Disc At Once) and CDRWIN applications. A cue sheet may also be needed when there is a mix of audio and data tracks to be burned (unless the burning software is told which tracks are which). A cue sheet may be needed when silent frames have been omitted from the beginning or end of files to be burned the cue sheet can be used to reconstruct the pauses by telling the burner or player where to insert silence. However, a cue sheet can be used to specify the location of the first track (if it deviates from the standard), as well as certain subcode information, such as non-01 index points, CD-TEXT (which may not exist on the original CD), UPC/ISRC data, and pre-emphasis information.Ī cue sheet is required to burn "hidden track one audio" ( HTOA), which is audio that can only be played after scanning backwards from the beginning of track 1. Comments (which are used by some programs to store nonstandard metadata like genre, freeDB disc ID, etc.)Ī cue sheet isn't necessary to make an exact copy of the audio portion of a CD ripping & burning software will get you the audio wave data and can figure out where each track starts.Gap info (how much silence to insert before or after each track).CD-Text metadata such as performer, title, songwriter for the disc and/or each track.The start point (index 01) for each track, time-wise (MM:SS:FF format).Ĭue sheets may contain the following additional info:.A numbered list of tracks each file corresponds to or contains.The name & type of at least one file being indexed (an audio file, normally).3.4.5 Single file version of the cue sheet used aboveĪll cue sheets contain the following info:.3.4.4 Multiple files with gaps (Noncompliant).3.4.3 Multiple files with gaps left out.3.4.2 Multiple files with corrected gaps.3.4.1 A single-file cue sheet with a TRACK 01 INDEX 00 hidden track.If there are any burning problems, use the Send Report options to send a failed operation log to the support team. ![]() Note: Click Save Log to save the current operation log. When burning is completed, you can save the log if needed. Wait until the burning process is completed.ġ6. Click Back to make any changes on previous pages.ġ5. R eview the Options Summary page and make sure all options are correct. You can also enable new burn sessions on this disc later by clicking Create multisession disc. Specify the desired speed from the list of supported burning speeds. If needed, select the Send optimum power calibration (OPC) checkbox to provide higher quality burning. It launches verification process right after disc burning.ġ1. The Verify written data option ensures that data has been written properly. Therefore, it allows for error checking and prevents damage of a media. Note: Test mode performs all steps of burning with a low-power laser without actually writing data. Select a burning mode and if needed enable Test mode and/or the Verify written data option. To change a disc label, either right-click the disc root and select Rename, or click the disc root and then click F2. Create a list of files and directories to burn using the drag-and-drop method. If you need to c reate a bootable disc, select the appropriate checkbox and specify the required information.ħ. ![]() Other available file systems are ISO 9660 Level 1, ISO 9660 Level 2 and UDF. The default file system type is ISO9660 + Joliet extensions. Select a burner from the list (the one you have inserted disc in).ģ. Insert a disc into the drive, if you have not done it yet.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |