Here’s a full side-by-side comparison of these products’ specs.Įvery 5° from 0° to 90°, plus 22.5° and 67. Both products have a rectangular-shaped bar and come with an adapter for T-slots. The bar on the KMS7101 has a length of 24”. The bar on the Miter 1000SE has a length of 17 1/4”. The bars on both miter gauges have a width of 3/4” and a depth of 3/8”. You can use a rectangular miter gauge bar in a T-slot, but not vice versa, since the T-shaped protrusions won’t fit. They can be either rectangular slots (with straight sides and bottom) or T-slots (with small indentations along the bottom edge that keep a miter gauge from slipping out). Most miter slots are 3/4” wide and 3/8” deep, though there are variations. You want to choose a miter gauge that fits your table saw’s miter slots, both in size and shape. The Miter 1000SE has a 31”-long fence and a stop that can be set with 1/32” precision. It may also have a stop attached to make repeatable cuts of the same length. Made from a soft aluminum designed to prevent. Step on the end of each setup bar used to test the fence depth of a tablesaw blade or router bit. Step on the top edge of each setup bar acts as a gauge to test the depth of your completed cuts. FenceĪ fence attached to the miter gauge’s head helps steady the workpiece for more precise cuts. The unique design straddles the router bit or saw blade to allow for more precise height adjustment. The Kreg has stops at 0°, 10°, 22.5°, 30°, and 45° and can be set to other angles with 0.01° precision. The INCRA has stops every 5° from 0° to 90°, plus 22.5° and 67.5° and can be set to other angles with 0.1° precision. Better miter gauges will have stops at more angles, and provide better precision. This ensures you are making precise cuts. The sizes marked on the bit are inch, inch, 1 inch, and 1 inch. stepped drill bit, stop collar, and thickness gauge/wrench. Older models have the setting built right into the clamp part, which is where you’ll set the collar. Stop Collar window reveals drill bit etchings for easy depth set up. Most miter gauges will have positive stops at common angles such as 45° and 90°. Depending on the age or type of your Kreg jig, it may or may not have the depth markings on the actual bit. Related: The Best Table Saw Miter Gauges Angle Stops & Precision They will be more than happy to help you.You can read our roundup of the best table saw miter gauges. If, after reviewing this, you are still needing assistance, please get in touch with the Kreg Customer Service Team. If not, or if you accidentally misplaced it, you can download and print a new copy for free here. You should've received one with your Kreg Jig HD. All of these steps, plus more tips and techniques to help you build successfully with the Kreg Jig HD, are included in the Owner Manual. In situations where using a clamp is not possible, you can fasten the Drill Guide directly to the workpiece by driving a screw through the hole in the center of the guide, as shown below. The position of the Depth Collar on the drill bit does not change. For repair applications, remove the Stop Block from the Drill Guide and clamp the Guide directly to the workpiece. The removable Stop Block allows you to use your Kreg Jig HD to repair or reinforce existing joints. With both parts clamped together, the self-tapping tip of the Kreg Jig HD Screw easily cuts through the last 1/16" of material in the first piece and forms its own pilot hole in the mating piece, drawing the joint tightly together. Also works with K5, K4, K3, R3, Mini, and Foreman. Note: Stopping the drill bit before it drills all the way through the workpiece eliminates splinters that have to be removed before joining it to a mating part. Stop collar and material-thickness gauge/wrench for Kreg Pocket-Hole Jigs. Fine-tune the position of the Stop Collar if necessary. With the Stop Collar resting on the Guide, there should be 1/16" (the thickness of a nickel) between the Stop Block and the tip of the drill bit. Slide the Kreg Jig HD drill bit into the Drill Guide. These clamps do not interlock with the Kreg Jig HD. When using an F-style clamp or a C-clamp, simply install the Stop Block. This grabs the Face Clamp's pad so the clamp stays in place on the Kreg Jig HD as you move it from one location to another. Then, install the Stop Block by sliding the tapered keys on the Stop Block into the mating slots in the bottom of the Drill Guide. If you are using a Kreg Face Clamp, slide the large clamp pad into the T-slot recess on the back of the Drill Guide. Slide the Stop Collar into the Kreg Jig HD Drill Bit, position it 4-3/4" from the shoulder of the bit, and tighten the set screw with the included hex wrench. Derek, To create the strongest joint possible, position the Stop Collar on your Kreg Jig HD drill bit following these three simple steps: 1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |